Network Working Group C. Chung Request for Comments: 2417 Independent Consultant Obsoletes: 2366 M. Greene Category: Standards Track Independent Contractor (Editor) September 1998
Definitions of Managed Objects for Multicast over UNI 3.0/3.1 based ATM Networks
Status of this Memo
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1998). All Rights Reserved.
IANA Note
Due to a clerical error in the assignment of the snmpModules in this memo, this RFC provides the corrected number assignment for this protocol. This memo obsoletes RFC 2366.
Abstract
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for IP hosts and routers that use a Multicast Address Resolution Server (MARS) to support IP multicast over ATM, as described in 'Support for Multicast over UNI 3.0/3.1 based ATM Networks' [1].
This memo specifies a MIB module in a manner that is both compliant to the SNMPv2 SMI, and semantically identical to the peer SNMPv1 definitions.
Chung & Greene Standards Track [Page 1]
RFC 2417 Multicast MIB September 1998
Table of Contents
1 The SNMP Network Management Framework ........................ 2 1.1 Object Definitions ......................................... 2 2 Overview ..................................................... 3 2.1 The MARS Client Group ...................................... 4 2.2 The MARS Server Group ...................................... 4 2.3 The MARS Multicast Server Group ............................ 5 3 IP over ATM Multicast Address Resolution Server MIB Definitions ............................................... 6 4 Acknowledgments ..............................................73 5 References ...................................................74 6 Security Considerations ......................................75 7 Authors' Addresses ...........................................75 8 Full Copyright Statement .....................................76
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object
Chung & Greene Standards Track [Page 2]
RFC 2417 Multicast MIB September 1998
type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type.
This MARS MIB is designed to define managed objects that can be used to manage the MARS clients, servers, and the multicast servers (MCS), as described in the RFC2022[1]. The MIB is supposed to be used on a system where one or more MARS clients are running, or where one or more MARS servers are running, or where one or more MARS multicast servers are running.
An understanding of MARS, as defined in [1] is assumed in this MIB module definition. However, the following terms are used frequently and are included here for reference:
Multicast Group
A group of endpoints that communicate with each other such that packets sent from one endpoint are received by all other members of the multicast group.
Multicast Address Resolution Server (MARS)
A server that distributes multicast group membership information to endpoints.
Client/Endpoint
An ATM-attached host or router that registers with a MARS and that is a member of one or more multicast groups. An endpoint may establish ATM Virtual Channels (VCs) to the other group members or may make use of a Multicast Server.
Cluster
The set of clients managed by a MARS.
Multicast Server (MCS)
A server that sets up ATM Virtual Channels (VCs) between endpoints in a multicast group and to which the endpoints forward data traffic for transmission on their behalf.
The MIB is broken down into three major groups: a MARS client group, MARS (server) group, and MARS Multicast Server (MCS) Group.
This client group defines a collection of objects required to be implemented in a MIB for the management of MARS clients. It contains the following tables:
o MARS Client Table
Information about a client such as its ATM address, the ATM address of its default MARS, registration status, and timers.
o MARS Client Multicast Group Table
A list of IP multicast address blocks associated with a MARS client.
o MARS Client Backup MARS Group Table
A list of backup MARS's associated with a MARS client.
This MARS server group defines a collection of objects required to be implemented in a MIB for the management of MARS servers. It contains the following tables:
o MARS Table
Information about a MARS such as its ATM address, its status and timers.
o MARS Multicast Group Table
A list of IP multicast address blocks associated with a MARS.
o MARS VC Table
Information about VCs opened by a MARS.
o MARS Registered Client Table
Chung & Greene Standards Track [Page 4]
RFC 2417 Multicast MIB September 1998
A list of clients registered with a MARS.
o MARS Registered Multicast Server Table
A list of MCSs registered with a MARS.
o MARS Statistics Table
Statistics collected by a MARS.
o MARS Host Map Table
Mappings between multicast groups and clients maintained by a MARS.
o MARS Server Map Table
Mappings between multicast groups and MCSs maintained by a MARS.
This MARS multicast server group defines a collection of objects required to be implemented in a MIB for the management of MARS multicast servers. It contains the following tables:
This group contains the following tables:
o MARS Multicast Server Table
Information about a MCS, such as its ATM address, default MARS ATM address, and registration state.
o MARS MCS Multicast Group Table
A list of IP multicast address blocks associated with a MARS MCS.
o MARS MCS Backup Mars Group Table
A list of backup MARS's associated with a MARS MCS.
o MARS Multicast Server VC Table
Information about VCs opened by a MCS.
o MARS Multicast Server Statistics Table
Statistics collected by a MCS.
Chung & Greene Standards Track [Page 5]
RFC 2417 Multicast MIB September 1998
3. IP Over ATM Multicast Address Resolution Server MIB Definitions
IPATM-IPMC-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF snmpModules, MODULE-IDENTITY, NOTIFICATION-TYPE, Counter32, Integer32, Unsigned32, OBJECT-TYPE, IpAddress FROM SNMPv2-SMI AtmAddr FROM ATM-TC-MIB TruthValue, RowStatus FROM SNMPv2-TC ipAdEntAddr FROM RFC1213-MIB InterfaceIndex FROM IF-MIB;
marsMIB MODULE-IDENTITY LAST-UPDATED "9809010000Z" -- 01 September 1998 ORGANIZATION "Internetworking Over NBMA (ion) Working Group" CONTACT-INFO " Chris Chung (chihschung@aol.com) Independent Consultant
Editor: Maria Greene Postal: Independent Contractor E-mail: maria@xedia.com " DESCRIPTION "This module defines a portion of the managed information base (MIB) for managing classical IP multicast address resolution server (MARS) and related entities as described in the RFC2022. This MIB is meant to be used in conjunction with the ATM-MIB (RFC1695), MIB-II (RFC1213), and optionally the IF-MIB (RFC1573). " REVISION "9809010000Z" -- 01 September 1998 DESCRIPTION "Published as RFC 2417. Changes/fixes: - reroot this MIB from snmpModules to mib-2 to be consistent with location of other MIBs. - obsoletes RFC2366." REVISION "9804150145Z" -- 15 April 1998 DESCRIPTION "Initial version, published as RFC 2366" ::= { mib-2 57 }
marsClientTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The objects defined in this table are used for the management of MARS clients, ATM attached endpoints." ::= { marsClientObjects 1 }
marsClientEntry OBJECT-TYPE SYNTAX MarsClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains a MARS client and its associated attributes. An entry in the marsClientTable has a corresponding entry in the ipAddrTable defined in RFC1213. Association between the ipAddrTable and the marsClientTable is made through the index, ipAdEntAddr." INDEX { ipAdEntAddr, marsClientIndex } ::= { marsClientTable 1 }
marsClientIndex OBJECT-TYPE SYNTAX Integer32(1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The auxiliary variable used to identify instances of the columnar objects in the MARS MarsClientTable." ::= { marsClientEntry 1 }
marsClientAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM address associated with the ATM Client." ::= { marsClientEntry 2 }
marsClientDefaultMarsAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The default MARS ATM address which is needed to setup the initial signalling path between a MARS client and its associated MARS." ::= { marsClientEntry 3 }
marsClientHsn OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The cluster membership own 32 bit Host Sequence Number. When a new cluster member starts up, it is initialized to zero. When the cluster member sends the MARS_JOIN to register, the HSN will be correctly set to the current cluster sequence number (CSN) when the Client receives the copy of its MARS_JOIN from the MARS. It is is used to track the MARS sequence number." ::= { marsClientEntry 4 }
registering (2), registered (3), reRegisteringFault (4), reRegisteringRedirMap (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication with regards to the registration status of this client. The registration codes of 'notRegistered (1)', 'registered (2)', and registered (3) are self-explanatory. The 'reRegisteringFault (4)' indicates the client is in the process of re-registering with a MARS due to some fault conditions. The 'reRegisteringRedMap (5)' status code shows that client is re-registering because it has received a MARS_REDIRECT_MAP message and was told to register with a different MARS from the current MARS." ::= { marsClientEntry 5 }
marsClientCmi OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "16 bit Cluster member identifier (CMI) assigned by the MARS which uniquely identifies each endpoint attached to the cluster. The value becomes valid after the 'marsClientRegistration' is set to the value of 'registered (1)'." ::= { marsClientEntry 6 }
marsClientDefaultMtu OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The default maximum transmission unit (MTU) used for this cluster. Note that the actual size used for a VC between two members of the cluster may be negotiated during connection setup and may be different than this value. Default value = 9180 bytes." DEFVAL { 9180 } ::= { marsClientEntry 7 }
UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A timer used to flag the failure of last MARS_MULTI to arrive. Default value = 10 seconds (recommended)." DEFVAL { 10 } ::= { marsClientEntry 8 }
marsClientRetranDelayTimer OBJECT-TYPE SYNTAX INTEGER (5..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The delay timer for sending out new MARS_REQUEST for the group after the client learned that there is no other group in the cluster. The timer must be set between 5 and 10 seconds inclusive." ::= { marsClientEntry 9 }
marsClientRdmMulReqAddRetrTimer OBJECT-TYPE SYNTAX INTEGER (5..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The initial random L_MULTI_RQ/ADD retransmit timer which can be set between 5 and 10 seconds inclusive." ::= { marsClientEntry 10 }
marsClientRdmVcRevalidateTimer OBJECT-TYPE SYNTAX INTEGER (1..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The random time to set VC_revalidate flag. The timer value ranges between 1 and 10 seconds inclusive." ::= { marsClientEntry 11 }
marsClientJoinLeaveRetrInterval OBJECT-TYPE SYNTAX INTEGER(5..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION
Chung & Greene Standards Track [Page 10]
RFC 2417 Multicast MIB September 1998
"MARS_JOIN/LEAVE retransmit interval. The minimum and recommended values are 5 and 10 seconds, respectively." DEFVAL { 10 } ::= { marsClientEntry 12 }
marsClientJoinLeaveRetrLimit OBJECT-TYPE SYNTAX INTEGER (0..5) MAX-ACCESS read-create STATUS current DESCRIPTION "MARS_JOIN/LEAVE retransmit limit. The maximum value is 5." ::= { marsClientEntry 13 }
marsClientRegWithMarsRdmTimer OBJECT-TYPE SYNTAX INTEGER (1..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Random time to register with MARS." ::= { marsClientEntry 14 }
marsClientForceWaitTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create STATUS current DESCRIPTION "Force wait if MARS re-registration is looping. The minimum value is 1 minute." ::= { marsClientEntry 15 }
marsClientLmtToMissRedirMapTimer OBJECT-TYPE SYNTAX INTEGER (1..4) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Timer limit for client to miss MARS_REDIRECT_MAPS." ::= { marsClientEntry 16 }
marsClientIdleTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create STATUS current
Chung & Greene Standards Track [Page 11]
RFC 2417 Multicast MIB September 1998
DESCRIPTION
"The configurable inactivity timer associated with a client. When a VC is created at this client, it gets the idle timer value from this configurable timer. The minimum suggested value is 1 minute and the recommended default value is 20 minutes." DEFVAL { 20 } ::= { marsClientEntry 17 }
marsClientRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
A row cannot be made 'active' until instances of all corresponding columns in the row of this table are appropriately configured and until the agent has also created a corresponding row in the marsClientStatTable.
When this object has a value of 'active', the following columnar objects can not be modified:
while other objects in this conceptual row can be modified irrespective of the value of this object.
Deletion of this row is allowed regardless of whether or not a row in any associated tables (i.e., marsClientVcTable) still exists or is in use. Once this row is deleted, it is recommended that the agent or the SNMP management station (if possible) through the set command deletes any stale rows that are associated with this row." ::= { marsClientEntry 18 }
-- IP ATM MARS Client Multicast Group Address Object Definitions --****************************************************************
marsClientMcGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsClientMcGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a list of IP multicast group address blocks associated with a MARS client. Entries in this table are used by the client that needs to receive or transmit packets from/to the specified range of multicast addresses. Each row can be created or deleted via configuration." ::= { marsClientObjects 2 }
marsClientMcGrpEntry OBJECT-TYPE SYNTAX MarsClientMcGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a consecutive block of multicast group addresses." INDEX { ipAdEntAddr, marsClientIndex, marsClientMcMinGrpAddr, marsClientMcMaxGrpAddr } ::= { marsClientMcGrpTable 1 }
marsClientMcMinGrpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum multicast group address - the min and max multicast forms multi-group block. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that this block contains a single group address." ::= { marsClientMcGrpEntry 1 }
marsClientMcMaxGrpAddr OBJECT-TYPE
Chung & Greene Standards Track [Page 13]
RFC 2417 Multicast MIB September 1998
SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum multicast group address - the min and max multicast forms a multi-group block. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that this block contains a single group address." ::= { marsClientMcGrpEntry 2 }
marsClientMcGrpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create or delete a row in this table.
Since other objects in this row are not-accessible 'index-objects', the value of this object has no effect on whether those objects in this conceptual row can be modified." ::= { marsClientMcGrpEntry 3 }
--**************************************************************** -- IP ATM MARS Client Backup MARS Object Definitions --****************************************************************
marsClientBackupMarsTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsClientBackupMarsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a list of backup MARS addresses that a client can connect to in case of failure for connecting to the primary server. The list of addresses is in descending order of preference. It should be noted that the backup list provided by the MARS to the client via the MARS_REDIRECT_MAP message has a higher preference than addresses that are manually configured into the client. When such a list is received from the MARS, this information should be inserted at the top of the list. Each row can be created or deleted via configuration." ::= { marsClientObjects 3 }
STATUS current DESCRIPTION "Each entry represents an ATM address of a backup MARS." INDEX { ipAdEntAddr, marsClientIndex, marsClientBackupMarsPriority, marsClientBackupMarsAddr } ::= { marsClientBackupMarsTable 1 }
marsClientBackupMarsPriority OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The priority associated with a backup MARS. A lower priority value inidcates a higher preference." ::= { marsClientBackupMarsEntry 1 }
marsClientBackupMarsAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM address associated with a backup MARS." ::= { marsClientBackupMarsEntry 2 }
marsClientBackupMarsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create or delete a row in this table.
Since other objects in this row are not-accessible 'index-objects', the value of this object has no effect on whether those objects in this conceptual row can be modified." ::= { marsClientBackupMarsEntry 3 }
-- IP ATM MARS Client VC Object Definition Table --***************************************************************
marsClientVcTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsClientVcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about open virtual circuits (VCs) that a client has. For point to point circuit, each entry represents a single VC connection between this client ATM address to another party ATM address. In the case of point to multipoint connection where a single source address is associated with multiple destinations, several entries are used to represent the relationship. An example of point to multi-point VC represented in a table is shown below.
Note: This table assumes the IP multicast address groups (min, max) defined in each entry are always consecutive. In the case of that a client receives a JOIN/LEAVE with mars$flag.punched set, each pair of the IP groups will first be broken into several pairs of consecutive IP groups before each entry row corresponding to a pair of IP group is created." ::= { marsClientObjects 4 }
marsClientVcEntry OBJECT-TYPE SYNTAX MarsClientVcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The objects contained in the entry are VC related attributes such as VC signalling type, control VC type, idle timer, negotiated MTU size, etc." INDEX { ipAdEntAddr, marsClientIndex, marsClientVcVpi, marsClientVcVci, marsClientVcMinGrpAddr, marsClientVcMaxGrpAddr,
marsClientVcVpi OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of virtual path identifier (VPI). Since a VPI can be numbered 0, this sub-index can take a value of 0." ::= { marsClientVcEntry 1 }
marsClientVcVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of virtual circuit identifier (VCI). Since a VCI can be numbered 0, this sub-index can take a value of 0." ::= { marsClientVcEntry 2 }
marsClientVcMinGrpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum IP multicast group address - the min and max multicast forms a multi-group consecutive block which is associated with a table entry.
Chung & Greene Standards Track [Page 17]
RFC 2417 Multicast MIB September 1998
if the MinGrpAddr and MaxGrpAddr are the same, it indicates that the size of multi-group block is 1, a single IP group." ::= { marsClientVcEntry 3 }
MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum IP multicast group address - the min and max multicast forms a multi-group consecutive block which is associated with a table entry. if the MinGrpAddr and MaxGrpAddr are the same, it indicates that the size of multi-group block is 1, a single IP group." ::= { marsClientVcEntry 4 }
marsClientVcPartyAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS not-accessible STATUS current DESCRIPTION "An ATM party address in which this VC is linked. The party type is identified by the marsClientVcPartyAddrType." ::= { marsClientVcEntry 5 }
marsClientVcPartyAddrType OBJECT-TYPE SYNTAX INTEGER { called (1), calling (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The party type is associated with the party address. The 'called (1)' indicates that the party address is a destination address which implies that VC is originated from this client. The 'calling (2)' indicates the VC was initiated externally to this client. In this case, the party address is the source address." ::= { marsClientVcEntry 6 }
marsClientVcType OBJECT-TYPE
Chung & Greene Standards Track [Page 18]
RFC 2417 Multicast MIB September 1998
SYNTAX INTEGER { pvc (1), svc (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Circuit Connection type: permanent virtual circuit or switched virtual circuit." ::= { marsClientVcEntry 7 }
marsClientVcCtrlType OBJECT-TYPE SYNTAX INTEGER { pointToPointVC (1), clusterControlVC (2), pointToMultiPointVC (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Control VC type used to specify a particular connection. pointToPointVC (1): used by the ATM Clients for the registration and queries. This VC or the initial signalling path is set up from the source Client to a MARS. It is bi-directional. clusterControlVC (2): used by a MARS to issue asynchronous updates to an ATM Client. This VC is established from the MARS to the ATM Client. pointToMultiPointVC (3): used by the client to transfer multicast data packets from layer 3. This VC is established from the source ATM Client to a destination ATM endpoint which can be a multicast group member or an MCS. The destination endpoint was obtained from the MARS." ::= { marsClientVcEntry 8 }
marsClientVcIdleTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create STATUS current DESCRIPTION "The idle timer associated with this VC. The minimum suggested value is 1 minute and the recommended default value is 20 minutes."
Chung & Greene Standards Track [Page 19]
RFC 2417 Multicast MIB September 1998
DEFVAL { 20 } ::= { marsClientVcEntry 9 }
marsClientVcRevalidate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A flag associated with an open and active multipoint VC. It is checked every time a packet is queued for transmission on that VC. The object has the value of true (1) if revalidate is required and the value false (2) otherwise." ::= { marsClientVcEntry 10 }
marsClientVcEncapsType OBJECT-TYPE SYNTAX INTEGER { other (1), llcSnap (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The encapsulation type used when communicating over this VC." ::= { marsClientVcEntry 11 }
marsClientVcNegotiatedMtu OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The negotiated MTU when communicating over this VC." ::= { marsClientVcEntry 12 }
marsClientVcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
A row cannot be made 'active' until instances of all corresponding columns in the row of this table are appropriately configured.
While objects: marsClientVcIdleTimer and
Chung & Greene Standards Track [Page 20]
RFC 2417 Multicast MIB September 1998
marsClientVcRevalidate in this conceptual row can be modified irrespective of the value of this object, all other objects in the row can not be modified when this object has a value of 'active'.
It is possible for an SNMP management station to set the row to 'notInService' and modify the entry and then set it back to 'active'
with the following exception. That is, rows for which the corresponding instance of marsClientVcType has a value of 'svc' can not be modified or deleted." ::= { marsClientVcEntry 13 }
--*************************************************************** -- IP ATM MARS Client Statistic Object Definition Table --***************************************************************
marsClientStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsClientStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains statistics collected at MARS clients." ::= { marsClientObjects 5 }
marsClientStatEntry OBJECT-TYPE SYNTAX MarsClientStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains statistics collected at one MARS client." INDEX { ipAdEntAddr, marsClientIndex } ::= { marsClientStatTable 1 }
marsClientStatTxReqMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_REQUEST messages transmitted from a client." ::= { marsClientStatEntry 1 }
marsClientStatTxJoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_JOIN messages transmitted from a client." ::= { marsClientStatEntry 2 }
marsClientStatTxLeaveMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_LEAVE messages transmitted from a client." ::= { marsClientStatEntry 3 }
marsClientStatTxGrpLstReqMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_GROUPLIST_REQUEST messages transmitted from a client." ::= { marsClientStatEntry 4 }
marsClientStatRxJoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_JOIN messages received by
Chung & Greene Standards Track [Page 22]
RFC 2417 Multicast MIB September 1998
a client." ::= { marsClientStatEntry 5 }
marsClientStatRxLeaveMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_LEAVE messages received by a client." ::= { marsClientStatEntry 6 }
marsClientStatRxMultiMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MULTI messages received by a client." ::= { marsClientStatEntry 7 }
marsClientStatRxNakMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_NAK messages received by a client." ::= { marsClientStatEntry 8 }
marsClientStatRxMigrateMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MIGRATE messages received by a client." ::= { marsClientStatEntry 9 }
marsClientStatRxGrpLstRplyMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_GROUPLIST_REPLY messages received by a client." ::= { marsClientStatEntry 10 }
Chung & Greene Standards Track [Page 23]
RFC 2417 Multicast MIB September 1998
marsClientStatFailMultiMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of timeouts occurred indicating failure of the last MARS_MULTI to arrive." ::= { marsClientStatEntry 11 }
--*************************************************************** -- IP ATM MARS Object Definitions --***************************************************************
marsObjects OBJECT IDENTIFIER ::= { marsMIB 2 }
marsTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The objects defined in this table are used for the management of MARS servers." ::= { marsObjects 1 }
marsEntry OBJECT-TYPE SYNTAX MarsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains a MARS and its associated attributes." INDEX { marsIndex, marsIfIndex } ::= { marsTable 1 }
marsIndex OBJECT-TYPE SYNTAX Integer32(1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The auxiliary variable used to identify instances of the columnar objects in the MARS table." ::= { marsEntry 1 }
marsIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex of the interface that the MARS is associated with." ::= { marsEntry 2 }
marsAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM address associated with the MARS." ::= { marsEntry 3 }
marsLocal OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A flag associated with a MARS entry. The object has the value of true (1) if the MARS whose interface is local to the machine that implements this MIB; otherwise the object has the value of false (2)." ::= { marsEntry 4 }
marsServStatus OBJECT-TYPE SYNTAX INTEGER { active (1), inactive (2), faulted (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The current status of MARS." ::= { marsEntry 5 }
Chung & Greene Standards Track [Page 25]
RFC 2417 Multicast MIB September 1998
marsServType OBJECT-TYPE SYNTAX INTEGER { primary (1), backup (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Types of MARS servers: primary or backup." ::= { marsEntry 6 }
marsServPriority OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Priority associated with a backup MARS server. A backup MARS server with lower priority value indicates a higher preference than other backup MARS servers to be used as the MARS server when the primary server fails." ::= { marsEntry 7 }
marsRedirMapMsgTimer OBJECT-TYPE SYNTAX INTEGER (1..2) UNITS "minutes" MAX-ACCESS read-create STATUS current DESCRIPTION "Periodic interval on which a multi-part MARS_REDIRECT_MAP is sent from this MARS." DEFVAL { 1 } ::= { marsEntry 8 }
marsCsn OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Current cluster sequence number (CSN) which is global within the context of a given protocol. The CSN is incremented by the MARS on every transmission of a message on ClusterControlVC. A cluster member uses the CSN to track the message loss on ClusterControlVC or to monitor a membership change." ::= { marsEntry 9 }
marsSsn OBJECT-TYPE
Chung & Greene Standards Track [Page 26]
RFC 2417 Multicast MIB September 1998
SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Current server sequence number (SSN) which is global within the context of a given protocol. The SSN is incremented by the MARS on every transmission of a message on ServerControlVC. A MCS uses the SSN to track the message loss on ServerControlVC or to monitor a membership change." ::= { marsEntry 10 }
marsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
A row cannot be made 'active' until instances of all corresponding columns in the row of this table are appropriately configured and until the agent has also created a corresponding row in the marsStatTable.
When this object has a value of 'active', the following columnar objects can not be modified:
while other objects in this conceptual row can be modified irrespective of the value of this object.
Deletion of this row is allowed regardless of whether or not a row in any associated tables (i.e., marsVcTable) still exists or is in use. Once this row is deleted, it is recommended that the agent or the SNMP management station (if possible) through the set command deletes any stale rows that are associated with this row." ::= { marsEntry 11 }
Chung & Greene Standards Track [Page 27]
RFC 2417 Multicast MIB September 1998
--**************************************************************** -- IP ATM MARS Multicast Group Address Object Definitions --****************************************************************
marsMcGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsMcGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a list of IP multicast address blocks associated with a MARS. Entries in this table are used by the MARS host map table and the server map table. They should be created prior to being referenced as indices by those tables. Each row can be created or deleted via configuration." ::= { marsObjects 2 }
marsMcGrpEntry OBJECT-TYPE SYNTAX MarsMcGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a consecutive block of multicast group addresses." INDEX { marsIndex, marsIfIndex, marsMcMinGrpAddr, marsMcMaxGrpAddr } ::= { marsMcGrpTable 1 }
marsMcMinGrpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum multicast group address - the min and max multicast forms multi-group block. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that this
Chung & Greene Standards Track [Page 28]
RFC 2417 Multicast MIB September 1998
block contains a single group address." ::= { marsMcGrpEntry 1 }
marsMcMaxGrpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum multicast group address - the min and max multicast forms a multi-group block. If The MinGrpAddr and MaxGrpAddr are the same, it indicates that this block contains a single group address." ::= { marsMcGrpEntry 2 }
marsMcGrpAddrUsage OBJECT-TYPE SYNTAX INTEGER { hostMap (1), serverMap (2), hostServerMap (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Usage of the multicast address block. The hostMap (1) indicates that the address block is only used in the MARS host map table. The serverMap (2) indicates that the address block is only used in the MARS server map table. The hostServerMap (3) indicates that the address block is used in both the host map and the server map tables." ::= { marsMcGrpEntry 3 }
marsMcGrpRxLayer3GrpSets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of MARS_JOIN messages received with mars$flags.layer3grp flag set." ::= { marsMcGrpEntry 4 }
marsMcGrpRxLayer3GrpResets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of MARS_JOIN messages received with mars$flags.layer3grp flag reset."
Chung & Greene Standards Track [Page 29]
RFC 2417 Multicast MIB September 1998
::= { marsMcGrpEntry 5 }
marsMcGrpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { marsMcGrpEntry 6 }
--*************************************************************** -- IP ATM MARS Host Map Object Definitions --***************************************************************
marsHostMapTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsHostMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table caches mappings between IP multicast address to a list of ATM addresses that are configured or dynamically learned from the MARS. This address resolution is used for the host map. It supports the mapping of a block of multicast group addresses to a cluster member address. In the case where a group block is associated with multiple cluster members, several entries are used to representing the relationship." ::= { marsObjects 3 }
marsHostMapEntry OBJECT-TYPE SYNTAX MarsHostMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry row contains attributes associated with the mapping between a multicast group block and an ATM address." INDEX { marsIndex, marsIfIndex, marsMcMinGrpAddr, marsMcMaxGrpAddr, marsHostMapAtmAddr } ::= { marsHostMapTable 1 }
marsHostMapAtmAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mapped cluster member ATM address." ::= { marsHostMapEntry 1 }
marsHostMapRowType OBJECT-TYPE SYNTAX INTEGER { static (1), dynamic (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Method in which this entry row is created. The static (1) indicates that this row is created through configuration. The dynamic (2) indicates that the row is created as the result of group address updates received at this MARS." ::= { marsHostMapEntry 2 }
marsHostMapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
This object must not be set to 'active' until instances of all corresponding columns in the row of this table are appropriately configured.
It is possible for an SNMP management station to set the row to 'notInService' and modify the entry and then set it back to 'active' with the following exception. That is, rows for which the corresponding instance of marsHostMapRowType has a value of 'dynamic'
Chung & Greene Standards Track [Page 31]
RFC 2417 Multicast MIB September 1998
can not be modified or deleted." ::= { marsHostMapEntry 3 }
--*************************************************************** -- IP ATM MARS Server Map Object Definitions --***************************************************************
marsServerMapTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsServerMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table caches mappings between IP multicast address to a list of MCS ATM addresses that are configured or dynamically learned from the MARS. This address resolution is used for the server map. It supports the mapping of a block of multicast group addresses to a MCS address. In the case where a group block is associated with multiple MCSs, several entries are used to representing the relationship." ::= { marsObjects 4 }
marsServerMapEntry OBJECT-TYPE SYNTAX MarsServerMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry row contains attributes associated with the mapping between a multicast group block and an MCS address." INDEX { marsIndex, marsIfIndex, marsMcMinGrpAddr, marsMcMaxGrpAddr, marsServerMapAtmAddr } ::= { marsServerMapTable 1 }
STATUS current DESCRIPTION "The mapped MCS ATM address." ::= { marsServerMapEntry 1 }
marsServerMapRowType OBJECT-TYPE SYNTAX INTEGER { static (1), dynamic (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Method in which this entry row is created. The 'static (1)' indicates that this row is created through configuration. The 'dynamic (2)' indicates that the row is created as the result of group address updates received at this MARS." ::= { marsServerMapEntry 2 }
marsServerMapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
This object must not be set to 'active' until instances of all corresponding columns in the row of this table are appropriately configured.
It is possible for an SNMP management station to set the row to 'notInService' and modify the entry and then set it back to 'active' with the following exception. That is, rows for which the corresponding instance of marsServerMapRowType has a value of 'dynamic' can not be modified or deleted." ::= { marsServerMapEntry 3 }
--*************************************************************** -- IP ATM MARS VC Object Definition Table --***************************************************************
marsVcTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsVcEntry MAX-ACCESS not-accessible
Chung & Greene Standards Track [Page 33]
RFC 2417 Multicast MIB September 1998
STATUS current DESCRIPTION "This table contains information about open virtual circuits (VCs) that a MARS has. For point to point circuit, each entry represents a single VC connection between this MARS ATM address to another party's ATM address. In the case of point to multipoint connection where a ControlVc is attached with multiple leaf nodes, several entries are used to represent the relationship. An example of point to multi-point VC represented in a table is shown below.
MARS VPI/VCI MARS Addr Party Addr 1 0,1 m1 p1 1 0,1 m1 p2 1 0,1 m1 p3" ::= { marsObjects 5 }
marsVcEntry OBJECT-TYPE SYNTAX MarsVcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The objects contained in the entry are VC related attributes such as VC signalling type, control VC type, idle timer, negotiated MTU size, etc." INDEX { marsIndex, marsIfIndex, marsVcVpi, marsVcVci, marsVcPartyAddr } ::= { marsVcTable 1 }
SYNTAX INTEGER (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of virtual path identifier (VPI). Since a VPI can be numbered 0, this sub-index can take a value of 0." ::= { marsVcEntry 1 }
marsVcVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of virtual circuit identifier (VCI). Since a VCI can be numbered 0, this sub-index can take a value of 0." ::= { marsVcEntry 2 }
marsVcPartyAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS not-accessible STATUS current DESCRIPTION "An ATM party address in which this VC is linked. The party type is identified by the marsVcPartyAddrType." ::= { marsVcEntry 5 }
marsVcPartyAddrType OBJECT-TYPE SYNTAX INTEGER { called (1), calling (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The party type is associated with the party address. The 'called (1)' indicates that the party address is a destination address which implies that VC is originated from this MARS. The 'calling (2)' indicates the VC was initiated externally to this MARS. The party address is the source address." ::= { marsVcEntry 6 }
} MAX-ACCESS read-create STATUS current DESCRIPTION "Circuit Connection type: permanent virtual circuit or switched virtual circuit." ::= { marsVcEntry 7 }
marsVcCtrlType OBJECT-TYPE SYNTAX INTEGER { pointToPointVC (1), clusterControlVC (2), serverControlVC (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Control VC type used to specify a particular connection. pointToPointVC (1): used by the ATM endpoints (clients) or the MCS for registration and queries. This VC is set up from a MARS client and MCS to this MARS. It is a bi-directional VC. clusterControlVC (2): used by MARS to issue asynchronous updates to ATM an ATM client. This VC is established from the MARs to the ATM client. serverControlVC (3): used by MARS to issue asynchronous update to ATM multicast servers. This type of VC exists when at least a MCS is being used." ::= { marsVcEntry 8 }
marsVcIdleTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create STATUS current DESCRIPTION "The idle timer associated with this VC. The minimum suggested value is 1 minute and the recommended default value is 20 minutes." DEFVAL { 20 } ::= { marsVcEntry 9 }
STATUS current DESCRIPTION "Cluster member identifier (CMI) which uniquely identifies each endpoint attached to the cluster. This variable applies to each 'leaf node' of an outgoing control VC." ::= { marsVcEntry 10 }
marsVcEncapsType OBJECT-TYPE SYNTAX INTEGER { other (1), llcSnap (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The encapsulation type used when communicating over this VC." ::= { marsVcEntry 11 }
marsVcNegotiatedMtu OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The negotiated MTU when communicating over this VC." ::= { marsVcEntry 12 }
marsVcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
A row cannot be made 'active' until instances of all corresponding columns in the row of this table are appropriately configured.
While the marsVcIdleTimer in this conceptual row can be modified irrespective of the value of this object, all other objects in the row can not be modified when this object has a value of 'active'.
It is possible for an SNMP management station to set the row to 'notInService' and modify the entry and then set it back to 'active'
Chung & Greene Standards Track [Page 37]
RFC 2417 Multicast MIB September 1998
with the following exception. That is, rows for which the corresponding instance of marsVcType has a value of 'svc' can not be modified or deleted." ::= { marsVcEntry 13 }
--*************************************************************** -- IP ATM MARS Registered Cluster Member List Table --***************************************************************
marsRegClientTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsRegClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ATM identities of all the currently registered cluster members at a MARS. Each entry represents one set of ATM identities associated with one cluster member or the MARS client." ::= { marsObjects 6 }
marsRegClientEntry OBJECT-TYPE SYNTAX MarsRegClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry row contains attributes associated with one register cluster member." INDEX { marsIndex, marsIfIndex, marsRegClientCmi} ::= { marsRegClientTable 1 }
marsRegClientCmi OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This cluster member identifier is used as an auxiliary index for the entry in this table." ::= { marsRegClientEntry 1 }
Chung & Greene Standards Track [Page 38]
RFC 2417 Multicast MIB September 1998
marsRegClientAtmAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-only STATUS current DESCRIPTION "The registered client's ATM address." ::= { marsRegClientEntry 2 }
--*************************************************************** -- IP ATM MARS Registered Server Member List Table --***************************************************************
marsRegMcsTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsRegMcsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ATM identities of all the currently registered MCSs at a MARS. Each entry represents one set of ATM identities associated with one MCS." ::= { marsObjects 7 }
marsRegMcsEntry OBJECT-TYPE SYNTAX MarsRegMcsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry row contains attributes associated with one registered MCS." INDEX { marsIndex, marsIfIndex, marsRegMcsAtmAddr } ::= { marsRegMcsTable 1 }
marsRegMcsAtmAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-only STATUS current DESCRIPTION "The registered MCS's ATM address." ::= { marsRegMcsEntry 1 }
Chung & Greene Standards Track [Page 39]
RFC 2417 Multicast MIB September 1998
--*************************************************************** -- IP ATM MARS Statistics Object Definition Table --***************************************************************
marsStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsStatEntry MAX-ACCESS not-accessible STATUS current
DESCRIPTION "The table contains statistics collected at MARS." ::= { marsObjects 8 }
marsStatEntry OBJECT-TYPE SYNTAX MarsStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains statistics collected at one MARS." INDEX { marsIndex, marsIfIndex } ::= { marsStatTable 1 }
SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MULTI transmitted by this MARS." ::= { marsStatEntry 1 }
marsStatTxGrpLstRplyMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_GROUPLIST_REPLY messages transmitted by this MARS." ::= { marsStatEntry 2 }
marsStatTxRedirectMapMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_REDIRECT_MAP messages transmitted by this MARS." ::= { marsStatEntry 3 }
marsStatTxMigrateMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MIGRATE messages transmitted by this MARS." ::= { marsStatEntry 4 }
marsStatTxNakMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_NAK messages transmitted by this MARS." ::= { marsStatEntry 5 }
marsStatTxJoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_JOIN messages transmitted by this
Chung & Greene Standards Track [Page 41]
RFC 2417 Multicast MIB September 1998
MARS." ::= { marsStatEntry 6 }
marsStatTxLeaveMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_LEAVE messages transmitted by this MARS." ::= { marsStatEntry 7 }
marsStatTxSjoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_SJOIN messages transmitted by this MARS." ::= { marsStatEntry 8 }
marsStatTxSleaveMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_SLEAVE messages transmitted by this MARS." ::= { marsStatEntry 9 }
marsStatTxMservMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MSERV messages transmitted by this MARS." ::= { marsStatEntry 10 }
marsStatTxUnservMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_UNSERV messages transmitted by this MARS." ::= { marsStatEntry 11 }
Chung & Greene Standards Track [Page 42]
RFC 2417 Multicast MIB September 1998
marsStatRxReqMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_REQUEST messages received by this MARS." ::= { marsStatEntry 12 }
marsStatRxGrpLstReqMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_GROUPLIST_REQUEST messages received by this MARS." ::= { marsStatEntry 13 }
marsStatRxJoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_JOINS messages received by this MARS." ::= { marsStatEntry 14 }
marsStatRxLeaveMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_LEAVES messages received by this MARS." ::= { marsStatEntry 15 }
marsStatRxMservMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MSERV messages received by this MARS." ::= { marsStatEntry 16 }
marsStatRxUnservMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_UNSERV messages received by this MARS."
Chung & Greene Standards Track [Page 43]
RFC 2417 Multicast MIB September 1998
::= { marsStatEntry 17 }
marsStatRxBlkJoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of block joins messages received by this MARS." ::= { marsStatEntry 18 }
marsStatRegMemGroups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of IP multicast groups with 1 or more joined cluster members." ::= { marsStatEntry 19 }
marsStatRegMcsGroups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of IP multicast groups with 1 or more joined MCSs." ::= { marsStatEntry 20 }
--*************************************************************** -- IP ATM MARS MCS Object Definitions --***************************************************************
marsMcsTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsMcsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The objects defined in this table are used for the management of a multicast server (MCS)." ::= { marsMcsObjects 1 }
marsMcsEntry OBJECT-TYPE SYNTAX MarsMcsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION
Chung & Greene Standards Track [Page 44]
RFC 2417 Multicast MIB September 1998
"Each entry contains a MCS and its associated attributes." INDEX { marsMcsIndex, marsMcsIfIndex } ::= { marsMcsTable 1 }
marsMcsIndex OBJECT-TYPE SYNTAX Integer32(1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The auxiliary variable used to identify instances of the columnar objects in the MCS table." ::= { marsMcsEntry 1 }
marsMcsIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex of the interface that the MCS is associated with." ::= { marsMcsEntry 2 }
STATUS current DESCRIPTION "The ATM address associated with the MCS." ::= { marsMcsEntry 3 }
marsMcsDefaultMarsAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The default MARS ATM address which is needed to setup the initial signalling path between a MCS and its associated MARS." ::= { marsMcsEntry 4 }
marsMcsRegistration OBJECT-TYPE SYNTAX INTEGER { notRegistered (1), registering (2), registered (3), reRegisteringFault (4), reRegisteringRedirMap (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication with regards to the registration STATUS of this MCS. The registration codes of 'notRegistered (1)', 'registered (2)', and registered (3) are self-explanatory. The 'reRegisteringFault (4)' indicates the MCS is in the process of re-registering with a MARS due to some fault conditions. The 'reRegisteringRedMap (5)' status code shows that MCS is re-registering because it has received a MARS_REDIRECT_MAP message and was told to register with a shift MARS." ::= { marsMcsEntry 5 }
marsMcsSsn OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The MCS own 32 bit Server Sequence Number. It is used to track the Mars sequence number." ::= { marsMcsEntry 6 }
marsMcsDefaultMtu OBJECT-TYPE
Chung & Greene Standards Track [Page 46]
RFC 2417 Multicast MIB September 1998
SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The default maximum transmission unit (MTU) used for this cluster. Note that the actual size used for a VC between two members of the cluster may be negotiated during connection setup and may be different than this value. Default value = 9180 bytes." DEFVAL { 9180 } ::= { marsMcsEntry 7 }
marsMcsFailureTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A timer used to flag the failure of last MARS_MULTI to arrive. Default value = 10 seconds (recommended)." DEFVAL { 10 } ::= { marsMcsEntry 8 }
marsMcsRetranDelayTimer OBJECT-TYPE SYNTAX INTEGER (5..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The delay timer for sending out new MARS_REQUEST for the group after the MCS learned that there is no other group in the cluster. The timer must be set between 5 and 10 seconds inclusive." ::= { marsMcsEntry 9 }
marsMcsRdmMulReqAddRetrTimer OBJECT-TYPE SYNTAX INTEGER (5..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The initial random L_MULTI_RQ/ADD retransmit timer which can be set between 5 and 10 seconds inclusive." ::= { marsMcsEntry 10 }
UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The random time to set VC_revalidate flag. The timer value ranges between 1 and 10 seconds inclusive." ::= { marsMcsEntry 11 }
marsMcsRegisterRetrInterval OBJECT-TYPE SYNTAX INTEGER(5..2147483647) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "MARS_MSERV/UNSERV retransmit interval. The minimum and recommended values are 5 and 10 seconds, respectively." DEFVAL { 10 } ::= { marsMcsEntry 12 }
marsMcsRegisterRetrLimit OBJECT-TYPE SYNTAX INTEGER (0..5) MAX-ACCESS read-create STATUS current DESCRIPTION "MARS_MSERV/UNSERV retransmit limit. The maximum value is 5." ::= { marsMcsEntry 13 }
marsMcsRegWithMarsRdmTimer OBJECT-TYPE SYNTAX INTEGER (1..10) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Random time for a MCS to register with a MARS." ::= { marsMcsEntry 14 }
marsMcsForceWaitTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create STATUS current DESCRIPTION "Force wait if MARS re-registration is looping. The minimum value is 1 minute." ::= { marsMcsEntry 15 }
Chung & Greene Standards Track [Page 48]
RFC 2417 Multicast MIB September 1998
marsMcsLmtToMissRedirMapTimer OBJECT-TYPE SYNTAX INTEGER (1..4) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Timer limit for MCS to miss MARS_REDIRECT_MAPS." ::= { marsMcsEntry 16 }
marsMcsIdleTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create STATUS current DESCRIPTION "The configurable inactivity timer associated with a MCS. When a VC is created at this MCS, it gets the idle timer value from this configurable timer. The minimum suggested value is 1 minute and the recommended default value is 20 minutes." DEFVAL { 20 } ::= { marsMcsEntry 17 }
marsMcsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
A row cannot be made 'active' until instances of all corresponding columns in the row of this table are appropriately configured and until the agent has also created a corresponding row in the marsMcsStatTable.
When this object has a value of 'active', the following columnar objects can not be modified:
while other objects in this conceptual row can be modified irrespective of the value of this object.
Chung & Greene Standards Track [Page 49]
RFC 2417 Multicast MIB September 1998
Deletion of this row is allowed regardless of whether or not a row in any associated tables (i.e., marsMcsVcTable) still exists or is in use. Once this row is deleted, it is recommended that the agent or the SNMP management station (if possible) through the set command deletes any stale rows that are associated with this row." ::= { marsMcsEntry 18 }
--**************************************************************** -- IP ATM MARS MCS Multicast Group Address Object Definitions --****************************************************************
marsMcsMcGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsMcsMcGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a list of IP multicast group address blocks associated by a MARS MCS. The MCS uses the information contained in list to advertise its multicast group service to the MARS. Each row can be created or deleted via configuration." ::= { marsMcsObjects 2 }
marsMcsMcGrpEntry OBJECT-TYPE SYNTAX MarsMcsMcGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a consecutive block of multicast group addresses." INDEX { marsMcsIndex, marsMcsIfIndex, marsMcsMcMinGrpAddr, marsMcsMcMaxGrpAddr } ::= { marsMcsMcGrpTable 1 }
SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum multicast group address - the min and max multicast forms multi-group block. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that this block contains a single group address. Since the block joins are no allowed by a MCS as implied in the RFC2022, the MinGrpAddr and MaxGrpAddress should be set to the same value at this time when an entry row is created." ::= { marsMcsMcGrpEntry 1 }
marsMcsMcMaxGrpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum multicast group address - the min and max multicast forms a multi-group block. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that this block contains a single group address. Since the block joins are no allowed by a MCS as implied in the RFC2022, the MinGrpAddr and MaxGrpAddress should be set to the same value at this time when an entry row is created." ::= { marsMcsMcGrpEntry 2 }
marsMcsMcGrpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create or delete a row in this table.
Since other objects in this row are not-accessible 'index-objects', the value of this object has no effect on whether those objects in this conceptual row can be modified." ::= { marsMcsMcGrpEntry 3 }
--**************************************************************** -- IP ATM MARS MCS Backup MARS Object Definitions --****************************************************************
marsMcsBackupMarsTable OBJECT-TYPE
Chung & Greene Standards Track [Page 51]
RFC 2417 Multicast MIB September 1998
SYNTAX SEQUENCE OF MarsMcsBackupMarsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a list of backup MARS addresses that a MCS can make contact to in case of failure for connecting to the primary server. The list of addresses is in descending order of preference. It should be noted that the backup list provided by the MARS to the MCS via the MARS_REDIRECT_MAP message has a higher preference than addresses that are manually configured into the MCS. When such a list is received from the MARS, this information should be inserted at the top of the list. Each row can be created or deleted via configuration." ::= { marsMcsObjects 3 }
marsMcsBackupMarsEntry OBJECT-TYPE SYNTAX MarsMcsBackupMarsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents an ATM address of a backup MARS." INDEX { marsMcsIndex, marsMcsIfIndex, marsMcsBackupMarsPriority, marsMcsBackupMarsAddr } ::= { marsMcsBackupMarsTable 1 }
marsMcsBackupMarsPriority OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The priority associated with a backup MARS. A lower priority value inidcates a higher preference." ::= { marsMcsBackupMarsEntry 1 }
marsMcsBackupMarsAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS not-accessible STATUS current
Chung & Greene Standards Track [Page 52]
RFC 2417 Multicast MIB September 1998
DESCRIPTION "The ATM address associated with a backup MARS." ::= { marsMcsBackupMarsEntry 2 }
marsMcsBackupMarsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create or delete a row in this table.
Since other objects in this row are not-accessible 'index-objects', the value of this object has no effect on whether those objects in this conceptual row can be modified." ::= { marsMcsBackupMarsEntry 3 }
--*************************************************************** -- IP ATM MARS MCS VC Object Definition Table --***************************************************************
marsMcsVcTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsMcsVcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about open virtual circuits (VCs) that a MCS has. For point to point circuit, each entry represents a single VC connection between this MCS ATM address to another party ATM address. In the case of point to multipoint connection where a single source address is associated with multiple destinations, several entries are used to represent the relationship. An example of point to multi-point VC represented in a table is shown below.
marsMcsVcEntry OBJECT-TYPE SYNTAX MarsMcsVcEntry MAX-ACCESS not-accessible STATUS current
Chung & Greene Standards Track [Page 53]
RFC 2417 Multicast MIB September 1998
DESCRIPTION "The objects contained in the entry are VC related attributes such as VC signalling type, control VC type, idle timer, negotiated MTU size, etc." INDEX { marsMcsIndex, marsMcsIfIndex, marsMcsVcVpi, marsMcsVcVci, marsMcsVcMinGrpAddr, marsMcsVcMaxGrpAddr, marsMcsVcPartyAddr } ::= { marsMcsVcTable 1 }
marsMcsVcVpi OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of virtual path identifier (VPI). Since a VPI can be numbered 0, this sub-index can take a value of 0." ::= { marsMcsVcEntry 1 }
marsMcsVcVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of virtual circuit identifier (VCI). Since a VCI can be numbered 0, this sub-index can take a value of 0."
Chung & Greene Standards Track [Page 54]
RFC 2417 Multicast MIB September 1998
::= { marsMcsVcEntry 2 }
marsMcsVcMinGrpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Minimum IP multicast group address - the min and max multicast forms a multi-group block which is associated with a VC. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that the size of multi-group block is 1, a single IP group." ::= { marsMcsVcEntry 3 }
marsMcsVcMaxGrpAddr OBJECT-TYPE
SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum IP multicast group address - the min and max multicast forms a multi-group block which is associated with a VC. If the MinGrpAddr and MaxGrpAddr are the same, it indicates that the size of multi-group block is 1, a single IP group." ::= { marsMcsVcEntry 4 }
marsMcsVcPartyAddr OBJECT-TYPE SYNTAX AtmAddr MAX-ACCESS not-accessible STATUS current DESCRIPTION "An ATM party address in which this VC is linked. The party type is identified by the marsMcsVcPartyAddrType." ::= { marsMcsVcEntry 5 }
marsMcsVcPartyAddrType OBJECT-TYPE SYNTAX INTEGER { called (1), calling (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The party type is associated with the party address. The called (1) indicates that the party address is
Chung & Greene Standards Track [Page 55]
RFC 2417 Multicast MIB September 1998
a destination address which implies that VC is originated from this MCS. The calling (2) indicates the VC was initiated externally to this MCS. In this case, the party address is the source address." ::= { marsMcsVcEntry 6 }
marsMcsVcType OBJECT-TYPE SYNTAX INTEGER { pvc (1), svc (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Circuit Connection type: permanent virtual circuit or switched virtual circuit." ::= { marsMcsVcEntry 7 }
marsMcsVcCtrlType OBJECT-TYPE SYNTAX INTEGER { pointToPointVC (1), serverControlVC (2), pointToMultiPointVC (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Control VC type used to specify a particular connection. pointToPointVC (1): used by the ATM Clients for the registration and queries. This VC or the initial signalling path is set up from the source MCS to a MARS. It is bi-directional. serverControlVC (2): used by a MARS to issue asynchronous updates to an ATM Client. This VC is established from the MARS to the MCS. pointToMultiPointVC (3): used by the client to transfer multicast data packets from layer 3. This VC is established from this VC to a cluster member." ::= { marsMcsVcEntry 8 }
marsMcsVcIdleTimer OBJECT-TYPE SYNTAX INTEGER (1..2147483647) UNITS "minutes" MAX-ACCESS read-create
Chung & Greene Standards Track [Page 56]
RFC 2417 Multicast MIB September 1998
STATUS current DESCRIPTION "The idle timer associated with this VC. The minimum suggested value is 1 minute and the recommended default value is 20 minutes." DEFVAL { 20 } ::= { marsMcsVcEntry 9 }
marsMcsVcRevalidate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A flag associated with an open and active multipoint VC. It is checked every time a packet is queued for transmission on that VC. The object has the value of true (1) if revalidate is required and the value false (2) otherwise." ::= { marsMcsVcEntry 10 }
marsMcsVcEncapsType OBJECT-TYPE SYNTAX INTEGER { other (1), llcSnap (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The encapsulation type used when communicating over this VC." ::= { marsMcsVcEntry 11 }
marsMcsVcNegotiatedMtu OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The negotiated MTU when communicating over this VC." ::= { marsMcsVcEntry 12 }
marsMcsVcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The object is used to create, delete or modify a row in this table.
Chung & Greene Standards Track [Page 57]
RFC 2417 Multicast MIB September 1998
A row cannot be made 'active' until instances of all corresponding columns in the row of this table are appropriately configured.
While objects: marsMcsVcIdleTimer and marsMcsVcRevalidate in this conceptual row can be modified irrespective of the value of this object, all other objects in the row can not be modified when this object has a value of 'active'.
It is possible for an SNMP management station to set the row to 'notInService' and modify the entry and then set it back to 'active' with the following exception. That is, rows for which the corresponding instance of marsMcsVcType has a value of 'svc' can not be modified or deleted." ::= { marsMcsVcEntry 13 }
--*************************************************************** -- IP ATM MARS MCS Statistics Definition Table --***************************************************************
marsMcsStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MarsMcsStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains statistics collected at MARS MCSs." ::= { marsMcsObjects 5 }
marsMcsStatEntry OBJECT-TYPE SYNTAX MarsMcsStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains statistics collected at one MARS MCS." INDEX { marsMcsIndex, marsMcsIfIndex } ::= { marsMcsStatTable 1 }
marsMcsStatTxReqMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_REQUEST messages transmitted from this MCS." ::= { marsMcsStatEntry 1 }
marsMcsStatTxMservMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MSERV messages transmitted from this MCS." ::= { marsMcsStatEntry 2 }
marsMcsStatTxUnservMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_UNSERV messages transmitted from this MCS." ::= { marsMcsStatEntry 3 }
marsMcsStatRxMultiMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MULTI messages received by this MCS." ::= { marsMcsStatEntry 4 }
marsMcsStatRxSjoinMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_SJOIN messages received by
Chung & Greene Standards Track [Page 59]
RFC 2417 Multicast MIB September 1998
this MCS." ::= { marsMcsStatEntry 5 }
marsMcsStatRxSleaveMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_SLEAVE messages received by this MCS." ::= { marsMcsStatEntry 6 }
marsMcsStatRxNakMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_NAK messages received by this MCS." ::= { marsMcsStatEntry 7 }
marsMcsStatRxMigrateMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of MARS_MIGRATE messages received by this MCS." ::= { marsMcsStatEntry 8 }
marsMcsStatFailMultiMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of timeouts occurred indicating failure of the last MARS_MULTI to arrive." ::= { marsMcsStatEntry 9 }
--*************************************************************** -- IP ATM MARS Notification Definitions --***************************************************************
marsServStatus } STATUS current DESCRIPTION "This trap/inform is sent to the manager whenever there is a fault condition occurred on a MARS." ::= { marsTrapInfo 1 }
--*************************************************************** -- IP ATM MARS Conformance Definitions --***************************************************************
--*************************************************************** -- MARS Client Compliance Statements --***************************************************************
marsClientCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that are required for the management of MARS clients." MODULE MANDATORY-GROUPS { marsClientGroup }
OBJECT marsClientAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientDefaultMarsAddr
Chung & Greene Standards Track [Page 61]
RFC 2417 Multicast MIB September 1998
MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientHsn MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientRegistration MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientCmi MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientDefaultMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientFailureTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientRetranDelayTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientRdmMulReqAddRetrTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsClientRdmVcRevalidateTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
marsClientLmtToMissRedirMapTimer, marsClientRowStatus, marsClientMcGrpRowStatus, marsClientBackupMarsRowStatus, marsClientVcPartyAddrType, marsClientVcType, marsClientVcCtrlType, marsClientVcIdleTimer, marsClientVcRevalidate, marsClientVcEncapsType, marsClientVcNegotiatedMtu, marsClientVcRowStatus, marsClientStatTxReqMsgs, marsClientStatTxJoinMsgs, marsClientStatTxLeaveMsgs, marsClientStatTxGrpLstReqMsgs, marsClientStatRxJoinMsgs, marsClientStatRxLeaveMsgs, marsClientStatRxMultiMsgs, marsClientStatRxNakMsgs, marsClientStatRxGrpLstRplyMsgs, marsClientStatRxMigrateMsgs, marsClientStatFailMultiMsgs } STATUS current DESCRIPTION "A collection of objects to be implemented in a MIB for the management of MARS clients." ::= { marsClientGroups 1 }
--*************************************************************** -- MARS Server Compliance Statements --***************************************************************
marsServerCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that are required for the management of MARS servers." MODULE -- this module MANDATORY-GROUPS { marsServerGroup, marsServerEventGroup }
OBJECT marsAddr MIN-ACCESS read-only DESCRIPTION
Chung & Greene Standards Track [Page 65]
RFC 2417 Multicast MIB September 1998
"Write access is not required."
OBJECT marsLocal MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsServStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsServType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsServPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsRedirMapMsgTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsCsn MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsSsn MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcGrpAddrUsage MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcGrpRowStatus
Chung & Greene Standards Track [Page 66]
RFC 2417 Multicast MIB September 1998
MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsHostMapRowType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsHostMapRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsServerMapRowType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsServerMapRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcPartyAddrType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcCtrlType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcIdleTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcCmi MIN-ACCESS read-only DESCRIPTION "Write access is not required."
Chung & Greene Standards Track [Page 67]
RFC 2417 Multicast MIB September 1998
OBJECT marsVcEncapsType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcNegotiatedMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsVcRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
marsStatTxRedirectMapMsgs, marsStatTxMigrateMsgs, marsStatTxNakMsgs, marsStatTxJoinMsgs, marsStatTxLeaveMsgs, marsStatTxSjoinMsgs, marsStatTxSleaveMsgs, marsStatTxMservMsgs, marsStatTxUnservMsgs, marsStatRxReqMsgs, marsStatRxGrpLstReqMsgs, marsStatRxJoinMsgs, marsStatRxLeaveMsgs, marsStatRxMservMsgs, marsStatRxUnservMsgs, marsStatRxBlkJoinMsgs, marsStatRegMemGroups, marsStatRegMcsGroups } STATUS current DESCRIPTION "A collection of objects to be implemented in a MIB for the management of MARS servers." ::= { marsServerGroups 1 }
marsServerEventGroup NOTIFICATION-GROUP NOTIFICATIONS { marsFaultTrap } STATUS current DESCRIPTION "A collection of events that can be generated from a MARS server." ::= { marsServerGroups 2 }
--*************************************************************** -- MARS Multicast Server (MCS) Compliance Statements --***************************************************************
marsMcsCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that are required for the management of MARS multicast servers (MCS)." MODULE MANDATORY-GROUPS { marsMcsGroup }
OBJECT marsMcsAddr
Chung & Greene Standards Track [Page 69]
RFC 2417 Multicast MIB September 1998
MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsDefaultMarsAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsRegistration MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsSsn MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsDefaultMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsFailureTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsRetranDelayTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsRdmMulReqAddRetrTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsRdmVcRevalidateTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsRegisterRetrInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required."
Chung & Greene Standards Track [Page 70]
RFC 2417 Multicast MIB September 1998
OBJECT marsMcsRegisterRetrLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsForceWaitTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsLmtToMissRedirMapTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsIdleTimer MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsMcGrpRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsBackupMarsRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsVcPartyAddrType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT marsMcsVcType MIN-ACCESS read-only DESCRIPTION "Write access is not required."
marsMcsVcPartyAddrType, marsMcsBackupMarsRowStatus, marsMcsVcType, marsMcsVcCtrlType, marsMcsVcIdleTimer, marsMcsVcRevalidate, marsMcsVcEncapsType, marsMcsVcNegotiatedMtu, marsMcsVcRowStatus, marsMcsStatTxReqMsgs, marsMcsStatTxMservMsgs, marsMcsStatTxUnservMsgs, marsMcsStatRxMultiMsgs, marsMcsStatRxSjoinMsgs, marsMcsStatRxSleaveMsgs, marsMcsStatRxNakMsgs, marsMcsStatRxMigrateMsgs, marsMcsStatFailMultiMsgs } STATUS current DESCRIPTION "A collection of objects to be implemented in a MIB for the management of MARS multicast servers (MCS)." ::= { marsMcsGroups 1 }
This document is a product of the IETF's Internetworking Over NBMA Networks (ion) Working Group. The original work of the MARS MIB developement was sponsored by Science Applications International Corporation (SAIC).
The author would like to recognize Grenville Armitage (Bellcore), Ken Carlberg (SAIC), Ramesh Uppuluri (Fore Systems), and Radha Gowda SYNNET), and Bill Willcox (Fujitsu Nexion) for their support and comments in completing the MARS MIB. Also thanks to Bert Wijnen (IBM) for his thorough review of the MARS MIB.
[1] Armitage, G., "Support for Multicast over UNI 3.0/3.1 based ATM Networks", RFC 2022, November 1996.
Chung & Greene Standards Track [Page 73]
RFC 2417 Multicast MIB September 1998
[2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, January 1996.
[3] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for Version 2 of the of the Simple Network Management Protocol (SNMPv2)", RFC 1903, January 1996.
[4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the of the Simple Network Management Protocol (SNMPv2)", RFC 1904, January 1996.
[5] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990.
[6] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996.
[7] McCloghrie, K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, March 1991.
[8] SNMPv3 Working Group, Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of Simple Network Management Protocol (SNMPv3)", RFC 2274, January 1998.
[9] SNMPv3 Working Group, Wijnen, B., Presuhn, R., and K. McCloghire, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2275, January 1998.
There are a number of management objects defined in this MIB that have a MAX-ACCESS clause of read-write and/or read-create. Such object may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations.
SNMPv1 by itself is such an insecure environment. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and SET (change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model RFC 2274 [8] and the View-based Access Control Model RFC 2275 [9] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity giving access to this MIB, is properly configured to give access to those objects only to those principals (users) that have a legitimate rights to indeed SET (change/create/delete) them.
Note: read-access in fact may also need access-control.
Copyright (C) The Internet Society (1998). All Rights Reserved.
This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English.
The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.