Internet Engineering Task Force (IETF) J. Ahlberg Request for Comments: 8561 Ericsson AB Category: Standards Track M. Ye ISSN: 2070-1721 Huawei Technologies X. Li NEC Laboratories Europe D. Spreafico Nokia - IT M. Vaupotic Aviat Networks June 2019
A YANG Data Model for Microwave Radio Link
Abstract
This document defines a YANG data model for control and management of radio link interfaces and their connectivity to packet (typically Ethernet) interfaces in a microwave/millimeter wave node. The data nodes for management of the interface protection functionality is broken out into a separate and generic YANG data model in order to make it available for other interface types as well.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc8561.
Ahlberg, et al. Standards Track [Page 1]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
This document defines a YANG data model for management and control of the radio link interface(s) and the relationship to packet (typically Ethernet) and/or Time-Division Multiplexing (TDM) interfaces in a microwave/millimeter wave node. The ETSI EN 302 217 series defines the characteristics and requirements of microwave/millimeter wave equipment and antennas. Specifically, ETSI EN 302 217-2 [EN302217-2] specifies the essential parameters for systems operating from 1.4 GHz to 86 GHz. The data model includes configuration and state data according to the new Network Management Datastore Architecture [RFC8342].
The design of the data model follows the framework for management and control of microwave and millimeter wave interface parameters defined in [RFC8432]. This framework identifies the need and the scope of the YANG data model, use cases, and requirements that the model needs to support. Moreover, it provides a detailed gap analysis to identify the missing parameters and functionalities of the existing and established models to support the specified use cases and requirements, and based on that, it recommends how the gaps should be filled with the development of the new model. According to the conclusion of the gap analysis, the structure of the data model is based on the structure defined in [MICROWAVE-RADIO-LINK], and it augments [RFC8343] to align with the same structure for management of the packet interfaces. More specifically, the model will include interface layering to manage the capacity provided by a radio link terminal for the associated Ethernet and TDM interfaces, using the principles for interface layering described in [RFC8343] as a basis.
The data nodes for management of the interface protection functionality is broken out into a separate and generic YANG data module in order to make it also available for other interface types.
The designed YANG data model uses established microwave equipment and radio standards, such as ETSI EN 302 217-2; the IETF Radio Link Model [MICROWAVE-RADIO-LINK]; and the ONF Microwave Model [ONF-model], as the basis for the definition of the detailed leafs/parameters, and it proposes new ones to cover identified gaps, which are analyzed in [RFC8432].
Carrier Termination (CT) is an interface for the capacity provided over the air by a single carrier. It is typically defined by its transmitting and receiving frequencies.
Ahlberg, et al. Standards Track [Page 3]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
Radio Link Terminal (RLT) is an interface providing packet capacity and/or TDM capacity to the associated Ethernet and/or TDM interfaces in a node and is used for setting up a transport service over a microwave/millimeter wave link.
A simplified graphical representation of the data model is used in Section 2.1 of this document. The meaning of the symbols in these diagrams is defined in [RFC8340].
The leafs in the Interface Management Module augmented by RLT and CT are not always applicable.
"/interfaces/interface/enabled" is not applicable for RLT. Enable and disable of an interface is done in the constituent CTs.
The packet-related measurements "in-octets", "in-unicast-pkts", "in-broadcast-pkts", "in-multicast-pkts", "in-discards", "in-errors", "in-unknown-protos", "out-octets", "out-unicast-pkts", "out- broadcast-pkts", "out-multicast-pkts", "out-discards", and "out- errors" are not within the scope of the microwave radio link domain and therefore are not applicable for RLT and CT.
Editors: Jonas Ahlberg (jonas.ahlberg@ericsson.com) Min Ye (amy.yemin@huawei.com) Xi Li (Xi.Li@neclab.eu) Daniela Spreafico (daniela.spreafico@nokia.com) Marko Vaupotic (Marko.Vaupotic@aviatnet.com)"; description "This is a module for the entities in a generic microwave system.
Copyright (c) 2019 IETF Trust and the persons identified as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
Ahlberg, et al. Standards Track [Page 8]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
This version of this YANG module is part of RFC 8561; see the RFC itself for full legal notices.";
revision 2019-06-19 { description "Initial revision."; reference "RFC 8561: A YANG Data Model for Microwave Radio Link"; }
/* * Features */
feature xpic { description "Indicates that the device supports XPIC."; reference "ETSI TR 102 311"; }
feature mimo { description "Indicates that the device supports MIMO."; reference "ETSI TR 102 311"; }
feature tdm { description "Indicates that the device supports TDM."; }
/* * Typedefs */
typedef power { type decimal64 { fraction-digits 1; } description "Type used for the power values in the data nodes for configuration or status."; }
Ahlberg, et al. Standards Track [Page 9]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
/* * Radio Link Terminal (RLT) */
augment "/if:interfaces/if:interface" { when "derived-from-or-self(if:type," + "'ianaift:microwaveRadioLinkTerminal')"; description "Addition of data nodes for the radio link terminal to the standard Interface data model, for interfaces of the type 'microwaveRadioLinkTerminal'."; leaf id { type string; description "Descriptive identity of the radio link terminal used by far-end RLT to check that it's connected to the correct near-end RLT. Does not need to be configured if this check is not used."; } leaf mode { type identityref { base mw-types:rlt-mode; } mandatory true; description "A description of the mode in which the radio link terminal is configured. The format is X plus Y. X represents the number of bonded carrier terminations. Y represents the number of protecting carrier terminations."; } leaf-list carrier-terminations { type if:interface-ref; must "derived-from-or-self(/if:interfaces/if:interface" + "[if:name = current()]" + "/if:type, 'ianaift:microwaveCarrierTermination')" { description "The type of interface must be 'microwaveCarrierTermination'."; } min-elements 1; description "A list of references to carrier terminations included in the radio link terminal."; }
Ahlberg, et al. Standards Track [Page 10]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
leaf-list rlp-groups { type leafref { path "/mrl:radio-link-protection-groups/" + "mrl:protection-group/mrl:name"; } description "A list of references to the carrier termination groups configured for radio link protection in this radio link terminal."; } leaf-list xpic-pairs { if-feature "xpic"; type leafref { path "/mrl:xpic-pairs/mrl:xpic-pair/mrl:name"; } description "A list of references to the XPIC pairs used in this radio link terminal. One pair can be used by two terminals."; reference "ETSI TR 102 311"; } leaf-list mimo-groups { if-feature "mimo"; type leafref { path "/mrl:mimo-groups/mrl:mimo-group/mrl:name"; } description "A reference to the MIMO group used in this radio link terminal. One group can be used by more than one terminal."; reference "ETSI TR 102 311"; } list tdm-connections { if-feature "tdm"; key "tdm-type"; description "A list stating the number of active TDM connections of a specified tdm-type that is configured to be supported by the RLT."; leaf tdm-type { type identityref { base mw-types:tdm-type; } description "The type of TDM connection, which also indicates the supported capacity.";
Ahlberg, et al. Standards Track [Page 11]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
} leaf tdm-connections { type uint16; mandatory true; description "Number of connections of the specified type."; } } }
/* * Carrier Termination */
augment "/if:interfaces/if:interface" { when "derived-from-or-self(if:type," + "'ianaift:microwaveCarrierTermination')"; description "Addition of data nodes for carrier termination to the standard Interface data model, for interfaces of the type 'microwaveCarrierTermination'."; leaf carrier-id { type string; default "A"; description "ID of the carrier (e.g., A, B, C, or D). Used in XPIC and MIMO configurations to check that the carrier termination is connected to the correct far-end carrier termination. Should be the same carrier ID on both sides of the hop. Left as default value when MIMO and XPIC are not in use."; } leaf tx-enabled { type boolean; default "false"; description "Disables (false) or enables (true) the transmitter. Only applicable when the interface is enabled (interface:enabled = true); otherwise, it's always disabled."; } leaf tx-oper-status { type enumeration { enum off { description "Transmitter is off."; } enum on {
Ahlberg, et al. Standards Track [Page 12]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
description "Transmitter is on."; } enum standby { description "Transmitter is in standby."; } } config false; description "Shows the operative status of the transmitter."; } leaf tx-frequency { type uint32; units "kHz"; mandatory true; description "Selected transmitter frequency."; } choice freq-or-distance { leaf rx-frequency { type uint32; units "kHz"; description "Selected receiver frequency."; } leaf duplex-distance { type int32; units "kHz"; description "Distance between transmitter and receiver frequencies."; } mandatory true; description "A choice to configure rx-frequency directly or compute it as duplex-distance subtracted from tx-frequency."; } leaf actual-rx-frequency { type uint32; units "kHz"; config false; description "Computed receiver frequency."; } leaf actual-duplex-distance { type uint32; units "kHz"; config false;
Ahlberg, et al. Standards Track [Page 13]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
description "Computed distance between Tx and Rx frequencies."; } leaf channel-separation { type uint32; units "kHz"; mandatory true; description "The amount of bandwidth allocated to a carrier. The distance between adjacent channels in a radio frequency channels arrangement"; reference "ETSI EN 302 217-1"; } leaf polarization { type enumeration { enum horizontal { description "Horizontal polarization."; } enum vertical { description "Vertical polarization."; } enum not-specified { description "Polarization not specified."; } } default "not-specified"; description "Polarization - a textual description for info only."; } choice power-mode { container rtpc { description "Remote Transmit Power Control (RTPC)."; reference "ETSI EN 302 217-1"; leaf maximum-nominal-power { type power { range "-99..99"; } units "dBm"; mandatory true; description "Selected output power.";
Ahlberg, et al. Standards Track [Page 14]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
reference "ETSI EN 302 217-1"; } } container atpc { description "Automatic Transmitter Power Control (ATPC)."; reference "ETSI EN 302 217-1"; leaf maximum-nominal-power { type power { range "-99..99"; } units "dBm"; mandatory true; description "Selected maximum output power. Minimum output power is the same as the system capability, minimum-power."; reference "ETSI EN 302 217-1"; } leaf atpc-lower-threshold { type power { range "-99..-20"; } units "dBm"; must 'current() <= ../atpc-upper-threshold'; mandatory true; description "The lower threshold for the input power at the far end, which is used in the ATPC mode."; reference "ETSI EN 302 217-1"; } leaf atpc-upper-threshold { type power { range "-99..-20"; } units "dBm"; mandatory true; description "The upper threshold for the input power at the far end, which is used in the ATPC mode."; reference "ETSI EN 302 217-1"; } }
Ahlberg, et al. Standards Track [Page 15]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
mandatory true; description "A choice of RTPC or ATPC."; } leaf actual-transmitted-level { type power { range "-99..99"; } units "dBm"; config false; description "Actual transmitted power level (0.1 dBm resolution)."; reference "ETSI EN 301 129"; } leaf actual-received-level { type power { range "-99..-20"; } units "dBm"; config false; description "Actual received power level (0.1 dBm resolution)."; reference "ETSI EN 301 129"; } choice coding-modulation-mode { container single { description "A single modulation order only."; reference "ETSI EN 302 217-1"; leaf selected-cm { type identityref { base mw-types:coding-modulation; } mandatory true; description "Selected the single coding/modulation."; } } container adaptive { description "Adaptive coding/modulation."; reference "ETSI EN 302 217-1";
Ahlberg, et al. Standards Track [Page 16]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
leaf selected-min-acm { type identityref { base mw-types:coding-modulation; } mandatory true; description "Selected minimum coding/modulation. Adaptive coding/modulation shall not go below this value."; } leaf selected-max-acm { type identityref { base mw-types:coding-modulation; } mandatory true; description "Selected maximum coding/modulation. Adaptive coding/modulation shall not go above this value."; } } mandatory true; description "A selection of single or adaptive coding/modulation mode."; } leaf actual-tx-cm { type identityref { base mw-types:coding-modulation; } config false; description "Actual coding/modulation in transmitting direction."; } leaf actual-snir { type decimal64 { fraction-digits 1; range "0..99"; } units "dB"; config false; description "Actual signal to noise plus the interference ratio (0.1 dB resolution)."; } leaf actual-xpi { if-feature "xpic"; type decimal64 {
Ahlberg, et al. Standards Track [Page 17]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
fraction-digits 1; range "0..99"; } units "dB"; config false; description "The actual carrier to cross-polar interference. Only valid if XPIC is enabled (0.1 dB resolution)."; reference "ETSI TR 102 311"; } container ct-performance-thresholds { description "Specification of thresholds for when alarms should be sent and cleared for various performance counters."; leaf received-level-alarm-threshold { type power { range "-99..-20"; } units "dBm"; default "-99"; description "An alarm is sent when the received power level is below the specified threshold."; reference "ETSI EN 301 129"; } leaf transmitted-level-alarm-threshold { type power { range "-99..99"; } units "dBm"; default "-99"; description "An alarm is sent when the transmitted power level is below the specified threshold."; reference "ETSI EN 301 129"; } leaf ber-alarm-threshold { type enumeration { enum 1e-9 { description "Threshold at 1e-9 (10^-9)."; } enum 1e-8 { description "Threshold at 1e-8 (10^-8).";
Ahlberg, et al. Standards Track [Page 18]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
} enum 1e-7 { description "Threshold at 1e-7 (10^-7)."; } enum 1e-6 { description "Threshold at 1e-6 (10^-6)."; } enum 1e-5 { description "Threshold at 1e-5 (10^-5)."; } enum 1e-4 { description "Threshold at 1e-4 (10^-4)."; } enum 1e-3 { description "Threshold at 1e-3 (10^-3)."; } enum 1e-2 { description "Threshold at 1e-2 (10^-2)."; } enum 1e-1 { description "Threshold at 1e-1 (10^-1)."; } } default "1e-6"; description "Specification of at which BER an alarm should be raised."; reference "ETSI EN 302 217-1"; } } leaf if-loop { type enumeration { enum disabled { description "Disables the IF Loop."; } enum client { description "Loops the signal back to the client side."; }
Ahlberg, et al. Standards Track [Page 19]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
enum radio { description "Loops the signal back to the radio side."; } } default "disabled"; description "Enable (client/radio) or disable (disabled) the IF Loop, which loops the signal back to the client side or the radio side."; } leaf rf-loop { type enumeration { enum disabled { description "Disables the RF Loop."; } enum client { description "Loops the signal back to the client side."; } enum radio { description "Loops the signal back to the radio side."; } } default "disabled"; description "Enable (client/radio) or disable (disabled) the RF loop, which loops the signal back to the client side or the radio side."; } container capabilities { config false; description "Capabilities of the installed equipment and some selected configurations."; leaf min-tx-frequency { type uint32; units "kHz"; description "Minimum Tx frequency possible to use."; } leaf max-tx-frequency { type uint32; units "kHz"; description "Maximum Tx frequency possible to use.";
Ahlberg, et al. Standards Track [Page 20]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
} leaf min-rx-frequency { type uint32; units "kHz"; description "Minimum Rx frequency possible to use."; } leaf max-rx-frequency { type uint32; units "kHz"; description "Maximum Tx frequency possible to use."; } leaf minimum-power { type power; units "dBm"; description "The minimum output power supported."; reference "ETSI EN 302 217-1"; } leaf maximum-available-power { type power; units "dBm"; description "The maximum output power supported."; reference "ETSI EN 302 217-1"; } leaf available-min-acm { type identityref { base mw-types:coding-modulation; } description "Minimum coding-modulation possible to use."; } leaf available-max-acm { type identityref { base mw-types:coding-modulation; } description "Maximum coding-modulation possible to use."; } } container error-performance-statistics { config false;
Ahlberg, et al. Standards Track [Page 21]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
description "ITU-T G.826 error performance statistics relevant for a microwave/millimeter wave carrier."; leaf bbe { type yang:counter32; units "number of block errors"; description "Number of Background Block Errors (BBEs). A BBE is an errored block not occurring as part of Severely Errored Seconds (SES). Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ITU-T G.826"; } leaf es { type yang:counter32; units "seconds"; description "Number of Errored Seconds (ES). An ES is a one-second period with one or more errored blocks or at least one defect. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ITU-T G.826"; } leaf ses { type yang:counter32; units "seconds"; description "Number of SES. SES is a one-second period that contains equal or more than 30% errored blocks or at least one defect. SES is a subset of ES. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ITU-T G.826"; } leaf uas { type yang:counter32; units "seconds"; description "Number of Unavailable Seconds (UAS); that is, the total time that the node has been unavailable.
Ahlberg, et al. Standards Track [Page 22]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ITU-T G.826"; } } container radio-performance-statistics { config false; description "ETSI EN 301 129 radio physical interface statistics relevant for a carrier termination."; leaf min-rltm { type power { range "-99..-20"; } units "dBm"; description "Minimum received power level. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ETSI EN 301 129"; } leaf max-rltm { type power { range "-99..-20"; } units "dBm"; description "Maximum received power level. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ETSI EN 301 129"; } leaf min-tltm { type power { range "-99..99"; } units "dBm";
Ahlberg, et al. Standards Track [Page 23]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
description "Minimum transmitted power level. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ETSI EN 301 129"; } leaf max-tltm { type power { range "-99..99"; } units "dBm"; description "Maximum transmitted power level. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of 'discontinuity-time' in ietf-interfaces."; reference "ETSI EN 301 129"; } } }
/* * Radio Link Protection Groups */
container radio-link-protection-groups { description "Configuration of radio link protected groups of carrier terminations in a radio link. More than one protected group per radio link terminal is allowed."; uses ifprot:protection-groups { refine "protection-group/members" { must "derived-from-or-self(/if:interfaces/if:interface" + "[if:name = current()]" + "/if:type, 'ianaift:microwaveCarrierTermination')" { description "The type of a protection member must be 'microwaveCarrierTermination'."; } } refine "protection-group/working-entity" { must "derived-from-or-self(/if:interfaces/if:interface" + "[if:name = current()]"
Ahlberg, et al. Standards Track [Page 24]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
+ "/if:type, 'ianaift:microwaveCarrierTermination')" { description "The type of a working-entity must be 'microwaveCarrierTermination'."; } } } }
/* * XPIC & MIMO groups - Configuration data nodes */
container xpic-pairs { if-feature "xpic"; description "Configuration of carrier termination pairs for operation in XPIC mode."; reference "ETSI TR 102 311"; list xpic-pair { key "name"; description "List of carrier termination pairs in XPIC mode."; leaf name { type string; description "Name used for identification of the XPIC pair."; } leaf enabled { type boolean; default "false"; description "Enable(true)/disable(false) XPIC"; } leaf-list members { type if:interface-ref; must "derived-from-or-self(/if:interfaces/if:interface" + "[if:name = current()]" + "/if:type, 'ianaift:microwaveCarrierTermination')" { description "The type of a member must be 'microwaveCarrierTermination'."; } min-elements 2; max-elements 2;
Ahlberg, et al. Standards Track [Page 25]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
description "Association to XPIC pairs used in the radio link terminal."; } } } container mimo-groups { if-feature "mimo"; description "Configuration of carrier terminations for operation in MIMO mode."; reference "ETSI TR 102 311"; list mimo-group { key "name"; description "List of carrier terminations in MIMO mode."; leaf name { type string; description "Name used for identification of the MIMO group."; } leaf enabled { type boolean; default "false"; description "Enable(true)/disable(false) MIMO."; } leaf-list members { type if:interface-ref; must "derived-from-or-self(/if:interfaces/if:interface" + "[if:name = current()]" + "/if:type, 'ianaift:microwaveCarrierTermination')" { description "The type of a member must be 'microwaveCarrierTermination'."; } min-elements 2; description "Association to a MIMO group if used in the radio link terminal."; } } } }
<CODE ENDS>
Ahlberg, et al. Standards Track [Page 26]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
The data nodes for management of the interface protection functionality is broken out from the Microwave Radio Link Module into a separate and generic YANG data model in order to make it also available for other interface types.
This module imports modules from [RFC8343], and it references [G.808.1].
Editors: Jonas Ahlberg (jonas.ahlberg@ericsson.com) Min Ye (amy.yemin@huawei.com) Xi Li (Xi.Li@neclab.eu) Daniela Spreafico (daniela.spreafico@nokia.com) Marko Vaupotic (Marko.Vaupotic@aviatnet.com)"; description "This is a module for the entities in a generic interface protection mechanism.
Copyright (c) 2019 IETF Trust and the persons identified as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
Ahlberg, et al. Standards Track [Page 27]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
This version of this YANG module is part of RFC 8561; see the RFC itself for full legal notices.";
revision 2019-06-19 { description "Initial revision."; reference "RFC 8561: A YANG Data Model for Microwave Radio Link"; }
identity one-plus-one-type { base protection-architecture-type; description "1+1; one interface protects another one interface."; reference "ITU-T G.808.1"; }
identity one-to-n-type { base protection-architecture-type; description "1:N; one interface protects n other interfaces."; reference "ITU-T G.808.1"; }
/* * Protection states identities */
identity protection-states { description "Identities describing the status of the protection in a group of interfaces configured in a protection mode.";
Ahlberg, et al. Standards Track [Page 28]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
}
identity unprotected { base protection-states; description "Not protected."; }
identity protected { base protection-states; description "Protected."; }
identity unable-to-protect { base protection-states; description "Unable to protect."; }
/* * Protection Groups */
grouping protection-groups { description "Configuration of protected groups of interfaces providing protection for each other. More than one protected group per higher-layer interface is allowed."; list protection-group { key "name"; description "List of protected groups of interfaces in a higher-layer interface."; leaf name { type string; description "Name used for identification of the protection group."; } leaf protection-architecture-type { type identityref { base protection-architecture-type; } default "ifprot:one-plus-one-type"; description "The type of protection architecture used, e.g., one interface protecting one or several other interfaces.";
Ahlberg, et al. Standards Track [Page 29]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
reference "ITU-T G.808.1"; } leaf-list members { type if:interface-ref; min-elements 2; description "Association to a group of interfaces configured for protection and used by a higher-layer interface."; } leaf operation-type { type enumeration { enum non-revertive { description "In non-revertive operation, the traffic does not return to the working interface if the switch requests are terminated."; reference "ITU-T G.808.1"; } enum revertive { description "In revertive operation, the traffic always returns to (or remains on) the working interface if the switch requests are terminated."; reference "ITU-T G.808.1"; } } default "non-revertive"; description "The type of protection operation, i.e., revertive or non-revertive operation."; } leaf-list working-entity { when "../operation-type = 'revertive'"; type if:interface-ref; min-elements 1; description "The interfaces that the traffic normally should be transported over when there is no need to use the protecting interface."; } leaf revertive-wait-to-restore { when "../operation-type = 'revertive'"; type uint16; units "seconds"; default "0";
Ahlberg, et al. Standards Track [Page 30]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
description "The time to wait before switching back to the working interface if operation-type is revertive."; reference "ITU-T G.808.1"; } leaf hold-off-timer { type uint16; units "milliseconds"; default "0"; description "Time interval after the detection of a fault and its confirmation as a condition requiring the protection- switching procedure."; reference "ITU-T G.808.1"; } leaf status { type identityref { base protection-states; } config false; description "Status of the protection in a group of interfaces configured in a protection mode."; reference "ITU-T G.808.1"; } action manual-switch-working { description "A switch action initiated by an operator command. It switches a normal traffic signal to the working transport entity."; reference "ITU-T G.808.1"; } action manual-switch-protection { description "A switch action initiated by an operator command. It switches a normal traffic signal to the protection transport entity."; reference "ITU-T G.808.1"; } action forced-switch { description "A switch action initiated by an operator command. It switches a normal traffic signal to the protection
Ahlberg, et al. Standards Track [Page 31]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
transport entity and forces it to remain on that entity even when criteria for switching back to the original entity are fulfilled."; reference "ITU-T G.808.1"; } action lockout-of-protection { description "A switch action temporarily disables access to the protection transport entity for all signals."; reference "ITU-T G.808.1"; } action freeze { description "A switch action temporarily prevents any switch action to be taken and, as such, freezes the current state. Until the freeze is cleared, additional near-end external commands are rejected, and fault condition changes and received Automatic Protection-Switching (APS) messages are ignored."; reference "ITU-T G.808.1"; } action exercise { description "A switch action to test if the APS communication is operating correctly. It is lower priority than any 'real' switch request."; reference "ITU-T G.808.1"; } action clear { description "An action clears all switch commands."; reference "ITU-T G.808.1"; } } } }
<CODE ENDS>
Ahlberg, et al. Standards Track [Page 32]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
This module defines a collection of common data types using the YANG data modeling language. These common types are designed to be imported by other modules defined in the microwave area.
Editors: Jonas Ahlberg (jonas.ahlberg@ericsson.com) Min Ye (amy.yemin@huawei.com) Xi Li (Xi.Li@neclab.eu) Daniela Spreafico (daniela.spreafico@nokia.com) Marko Vaupotic (Marko.Vaupotic@aviatnet.com)"; description "This module contains a collection of YANG data types considered generally useful for microwave interfaces.
Copyright (c) 2019 IETF Trust and the persons identified as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC 8561; see the RFC itself for full legal notices.";
revision 2019-06-19 { description "Initial revision."; reference "RFC 8561: A YANG Data Model for Microwave Radio Link"; }
Ahlberg, et al. Standards Track [Page 33]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
/* * Radio-link-terminal mode identities */
identity rlt-mode { description "A description of the mode in which the radio link terminal is configured. The format is X plus Y. X represents the number of bonded carrier terminations. Y represents the number of protecting carrier terminations."; }
The YANG data models specified in this document define schemas for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].
The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.
There are a number of data nodes defined in these YANG data models that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability:
Interfaces of type microwaveRadioLinkTerminal:
/if:interfaces/if:interface/mode, /if:interfaces/if:interface/carrier-terminations, /if:interfaces/if:interface/rlp-groups, /if:interfaces/if:interface/xpic-pairs, /if:interfaces/if:interface/mimo-groups, and /if:interfaces/if:interface/tdm-connections:
These data nodes represent the configuration of the radio link terminal, and they need to match the configuration of the radio link terminal on the other side of the radio link. Unauthorized access to these data nodes could interrupt the ability to forward traffic.
RFC 8561 Microwave Radio Link YANG Data Model June 2019
/if:interfaces/if:interface/atpc/maximum-nominal-power, /if:interfaces/if:interface/atpc/atpc-lower-threshold, /if:interfaces/if:interface/atpc/atpc-upper-threshold, /if:interfaces/if:interface/single/selected-cm, /if:interfaces/if:interface/adaptive/selected-min-acm, /if:interfaces/if:interface/adaptive/selected-max-acm, /if:interfaces/if:interface/if-loop, and /if:interfaces/if:interface/rf-loop:
These data nodes represent the configuration of the carrier termination, and they need to match the configuration of the carrier termination on the other side of the carrier. Unauthorized access to these data nodes could interrupt the ability to forward traffic.
Radio link protection:
/radio-link-protection-groups/protection-group:
This data node represents the configuration of the protection of carrier terminations. Unauthorized access to this data node could interrupt the ability to forward traffic or remove the ability to perform a necessary protection switch.
XPIC:
/xpic-pairs:
This data node represents the XPIC configuration of a pair of carriers. Unauthorized access to this data node could interrupt the ability to forward traffic.
MIMO:
/mimo-groups:
This data node represents the MIMO configuration of multiple carriers. Unauthorized access to this data node could interrupt the ability to forward traffic.
Some of the RPC operations in this YANG data model may be considered sensitive or vulnerable in some network environments. It is thus important to control access to these operations. These are the operations and their sensitivity/vulnerability:
Ahlberg, et al. Standards Track [Page 41]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
Radio link protection:
/radio-link-protection-groups/protection-group/manual-switch-working, /radio-link-protection-groups/protection-group/ manual-switch-protection, /radio-link-protection-groups/protection-group/forced-switch, /radio-link-protection-groups/protection-group/lockout-of-protection, /radio-link-protection-groups/protection-group/freeze, /radio-link-protection-groups/protection-group/exercise, and /radio-link-protection-groups/protection-group/clear
These data nodes represent actions that might have an impact on the configuration of the protection of carrier terminations. Unauthorized access to these data nodes could interrupt the ability to forward traffic or remove the ability to perform a necessary protection switch.
The security considerations of [RFC8343] also apply to this document.
IANA has assigned new URIs from the "IETF XML Registry" [RFC3688] as follows:
URI: urn:ietf:params:xml:ns:yang:ietf-microwave-radio-link Registrant Contact: The IESG XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:ietf-interface-protection Registrant Contact: The IESG XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:ietf-microwave-types Registrant Contact: The IESG XML: N/A; the requested URI is an XML namespace.
Ahlberg, et al. Standards Track [Page 42]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
IANA has recorded YANG module names in the "YANG Module Names" registry [RFC6020] as follows:
Name: ietf-microwave-radio-link Maintained by IANA?: N Namespace: urn:ietf:params:xml:ns:yang:ietf-microwave-radio-link Prefix: mrl Reference: RFC 8561
Name: ietf-interface-protection Maintained by IANA?: N Namespace: urn:ietf:params:xml:ns:yang:ietf-interface-protection Prefix: ifprot Reference: RFC 8561
Name: ietf-microwave-types Maintained by IANA?: N Namespace: urn:ietf:params:xml:ns:yang:ietf-microwave-types Prefix: mw-types Reference: RFC 8561
IANA has registered the following ifTypes in "ifType definitions" under [IANA-SMI]:
Decimal Name Description ------- ------------ ------------------------------- 295 microwaveCarrierTermination air interface of a single microwave carrier
296 microwaveRadioLinkTerminal radio link interface for one or several aggregated microwave carriers
[EN301129] ETSI, "Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); Synchronous Digital Hierarchy (SDH); System performance monitoring parameters of SDH DRRS", EN 301 129 V1.1.2, May 1999.
Ahlberg, et al. Standards Track [Page 44]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
[EN302217-1] ETSI, "Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview, common characteristics and system- dependent requirements", EN 302 217-1 V3.1.0, May 2017.
[EN302217-2] ETSI, "Fixed Radio Systems; Characteristics and requirements for point to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU", EN 302 217-2 V3.1.1, May 2017.
[G.808.1] ITU-T, "SERIES G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS; Digital networks ; General aspects Generic protection switching ; Linear trail and subnetwork protection", ITU-T Recommendation G.808.1, May 2014.
[G.826] ITU-T, "SERIES G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS; Digital networks - Quality and availability targets; End-to-end error performance parameters and objectives for international, constant bit- rate digital paths and connections", ITU-T Recommendation G.826, December 2002.
[MICROWAVE-RADIO-LINK] Ahlberg, J., Carlson, J., Lund, H., Olausson, T., Ye, M., and M. Vaupotic, "Microwave Radio Link YANG Data Models", Work in Progress, draft-ahlberg-ccamp-microwave-radio- link-01, May 2016.
RFC 8561 Microwave Radio Link YANG Data Model June 2019
[RFC8432] Ahlberg, J., Ed., Ye, M., Ed., Li, X., Contreras, LM., and CJ. Bernardos, "A Framework for Management and Control of Microwave and Millimeter Wave Interface Parameters", RFC 8432, DOI 10.17487/RFC8432, October 2018, <https://www.rfc-editor.org/info/rfc8432>.
[TR102311] ETSI, "Fixed Radio Systems; Point-to-point equipment; Specific aspects of the spatial frequency reuse method", ETSI TR 102 311 V1.2.1, November 2015.
Ahlberg, et al. Standards Track [Page 46]
RFC 8561 Microwave Radio Link YANG Data Model June 2019
Appendix A. Example: 1+0 and 2+0 Configuration Instances
This section gives simple examples of 1+0 and 2+0 instances using the YANG data model defined in this document. The examples are not intended as a complete module for 1+0 and 2+0 configuration.